 PRODUCTS INTERNATIONAL |
|||||
|
Female Belts Male Belts Accessories Restraints Jewellery Measurements Prices Contact Gallery Information Introduction Spare parts |
|||||
PRIVATE AND CONFIDENTIAL | |||||
| Description | |||||
| Step 1 | Measure the waist as it normally is. Pull the waist in as far as possible and then measure it again. This is just to establish a preliminary base line. |  |
 |
||
| Step 2 | Fasten around the waist a one inch (25mm) wide belt making sure that it is horizontal and not dipped down in front. Make a mark on the centre front of the person being measured level with the underside of the belt. (Depending on anatomy this maybe above, below or on the belly button) |  |
 |
||
| Step 3 | Adjust the belt to the smallest circumference at which you feel you could wear it and mark the position on the belt. Do not be tempted to settle for a nice comfortable fit, aim at a tight rather than a loose fit. Remove the belt, lay it out flat and measure from the end to the reference mark to determine the length. |  |
|||
| Step 4 | From the point marked in step 1 measure downward toward the penis a distance equal to 1/8 of the measurement you got in step 2 and mark this point on the body with a felt tip marker or similar. |
 |
|||
| Step 5 | From the point marked in step 3 measure down to the base of the penis. Measurement G. |  | Side | Back | |
| Step 6 | From the point marked in step 3, measure down between the legs to the anus; do not take the tape over the penis or scrotum but to one side of it keeping as straight as possible. This is a very important measurement for the sake of accuracy it is worth repeating several times. The person being measured should maintain an upright position during this procedure. (Do not bend over). This is measurement I. |  |
|||
| Step 7 | With the belt in position, find the centre back of the waist and mark it. Make a mark three inches to the right of it and a further one three inches to the left of it. Measure from the mark made in step 3 down between the legs and up over the buttocks to the right hand mark at the rear waist; bottom edge of the belt. Repeat this procedure to the left-hand mark, this measurement is usually the same and serves as double check. Try to make sure the tape stays flat and in contact all the way, again do not measure over the penis or scrotum but to either side keeping the tape as straight as possible. Exercise care with these measurements. Measurement J. |  |
 |
 |
|
 |
 |
 |
|||
| Step 8 | With belt still in place, measure from the mark you made at front centre in step 3 to the bottom edge of the belt at back centre. Make sure the tape fits snugly up between the buttocks, again not over the penis or scrotum but to one side. Measurement K. |  Back |
|||
| Step 9 | Measure from the bottom edge centre back down to the anus, keeping the tape a snug fit between the buttocks. Measurement L. |  |
 |
 |
|
| Step 10 | Repeat step 1 but passing the belt above the hips at waist level and then dipping down to pass over the lower mark you just made in step 3. Adjust the belt to the smallest circumference at which you feel you could wear it and mark the position on the belt. Do not be tempted to settle for a nice comfortable fit, aim at a tight rather than a loose fit. |  |
 |
||
| Step 11 | Measure largest circumference over the hips. If this is not bigger than the waist measurement then then belt will not work as it can be pulled down. |  |
|||
| Step 12 | Measure penis length fully relaxed. |  |
|||
| Step 13 | Measure penis circumference fully relaxed. (mid point) |  |
|||
| Step 14 | Measure penis length at full erection. |  |
|||
| Step 15 | Measure penis circumference at full erection. (mid point) | |
|||
|
Many Tollyboy products are copied, but none equal our quality. |
|||||